Strips aluminum tread plate Mold 0.018-1.0mm Thick
When you need a lightweight, corrosion-resistant surface that also provides reliable traction, strips aluminum tread plate (also called checker plate or diamond plate) is a proven choice. Our Strips Aluminum Tread Plate Mold (0.018–1.0mm thick) is designed for customers who want the anti-slip benefits of tread patterning in a thin, coil-friendly strip format-easy to fabricate, economical to ship, and adaptable to both industrial and decorative uses.
Thin-gauge tread plate is especially valuable where conventional thick plate is overbuilt: interior vehicle panels, appliance trim, protective cladding, lightweight platforms, packaging lines, and architectural accents. The embossed tread pattern adds stiffness and grip without the mass of heavy plate, while aluminum's natural oxide layer provides long-term corrosion resistance.
Strips Aluminum Tread Plate Mold 0.018–1.0mm Thick refers to aluminum strip that is rolled/embossed with a raised tread pattern and delivered in coils or cut lengths. The "mold" wording typically indicates the patterning roll set / embossing tooling used to form consistent tread geometry along the strip.
value points include:
- Anti-slip surface for safer handling and walking contact in light-duty environments
- Improved stiffness-to-weight vs. flat sheet at the same thickness
- Excellent corrosion resistance for indoor, humid, and many outdoor conditions
- High formability options (depending on alloy/temper) for bending, edging, and profiling
- Attractive industrial finish suitable for visible applications
Features That Matter in Thin Tread Plate
Anti-slip traction without bulky thickness
The raised pattern increases friction and helps reduce slip risk from water, dust, or light oils. In thin gauges, this is ideal for liners, access covers, step facings, and protective skins where weight and bendability are important.
Pattern-driven rigidity
Even at 0.018–1.0mm, the embossed geometry acts like micro-stiffeners. This can reduce oil-canning and improve panel feel in vehicle interiors, equipment housings, and cladding.
Corrosion performance and low maintenance
Aluminum alloys commonly used for tread strip maintain a protective oxide film. With proper alloy selection, they perform well in humid plants, coastal logistics, and washdown-adjacent areas.
Fabrication-friendly strip format
Coiled strip supports high-throughput processing such as roll forming, stamping, slitting, and press brake bending. Thin gauges also lower forming loads and improve throughput.
Common Alloy Options and Why They're Selected
Different applications demand different balances of corrosion resistance, strength, and formability. Below are widely used options for thin tread strip production.
Typical Chemical Composition (Reference Ranges)
Actual composition can be tailored to relevant standards (ASTM/EN/JIS) and customer specifications. Values below are typical reference ranges for common alloys.
| Alloy | Si (%) | Fe (%) | Cu (%) | Mn (%) | Mg (%) | Cr (%) | Zn (%) | Ti (%) | Al |
|---|---|---|---|---|---|---|---|---|---|
| 1050/1100 (1xxx) | ≤0.25–0.95 | ≤0.40–0.95 | ≤0.05–0.20 | ≤0.05 | ≤0.05 | - | ≤0.10 | ≤0.05 | Balance |
| 3003 (3xxx) | ≤0.60 | ≤0.70 | ≤0.05–0.20 | 1.0–1.5 | - | - | ≤0.10 | ≤0.10 | Balance |
| 5052 (5xxx) | ≤0.25 | ≤0.40 | ≤0.10 | ≤0.10 | 2.2–2.8 | 0.15–0.35 | ≤0.10 | ≤0.10 | Balance |
Selection guidance (practical):
| Priority | Recommended Alloy Family | Notes |
|---|---|---|
| Maximum formability, bright finish | 1xxx | Best for decorative/protective skins and deep bends; lower strength |
| Balanced forming + strength, good corrosion | 3003 | Popular general-purpose choice for panels and guards |
| Higher strength + superior marine corrosion | 5052 | Stronger and more corrosion-resistant; slightly higher forming force |
Technical Specifications (Strips, Thin Gauge)
Specifications can be adjusted by agreement; the table below summarizes common supply capabilities for 0.018–1.0mm tread strip.
| Item | Typical Range / Options |
|---|---|
| Thickness (base metal) | 0.018–1.0 mm |
| Width | 20–1250 mm (custom slit widths available) |
| Coil ID | 150 / 300 / 505 mm (by request) |
| Coil OD | Up to ~1200–1600 mm (depends on thickness/weight) |
| Coil weight | ~0.3–5.0 tons (custom packaging available) |
| Tread pattern | Diamond / 5-bar / custom emboss (by tooling) |
| Surface finish | Mill finish, bright, brushed (option), coated (option) |
| Temper | O, H12, H14, H16, H18, H22, H24 (by alloy and application) |
| Edge | Mill edge or slit edge |
| Protective options | Interleaving paper, PE film, anti-scratch packaging |
| Standards | ASTM B209 / EN 485 / JIS H4000 (as agreed) |
Dimensional and Pattern Considerations (Thin Tread)
In thin gauges, the embossed pattern can influence final formed thickness and flatness. For critical assemblies, confirm the following:
| Parameter | What It Impacts | Typical Control Focus |
|---|---|---|
| Pattern height / pitch | Grip level, stiffness, aesthetics | Consistency along coil length |
| Thickness tolerance | Fit-up, forming repeatability | Tight tolerances for roll forming |
| Flatness | Lamination, panel appearance | Controlled by leveling and coil handling |
| Surface quality | Visible components | Scratch limits, film protection |
Performance Snapshot (Practical Expectations)
| Property | 1xxx Series | 3003 | 5052 |
|---|---|---|---|
| Formability | Excellent | Very good | Good |
| Corrosion resistance | Excellent | Excellent | Outstanding (especially marine) |
| Strength level | Low | Medium | Medium-high |
| Best-fit applications | Decorative trims, light cladding | General panels, guards | Transport, outdoor hardware, corrosive areas |
Note: Mechanical properties vary significantly with temper; specify temper based on bending radius, stiffness needs, and dent resistance targets.
Applications: Where Thin Tread Strips Excel
Transportation and mobility
Thin tread strip is widely used where designers want grip plus a rugged look without adding heavy plate. Typical uses include:
- Bus, van, and trailer interior panels
- Step facings and kick plates
- Toolbox liners and compartment cladding
- Protective wear strips in high-contact zones
Industrial equipment and factory environments
Embossed strip brings surface durability and stiffness to machine-adjacent areas:
- Machine guards and protective shrouds
- Conveyor side panels and inspection covers
- Light-duty platforms, catwalk skins, and maintenance panels
- Packaging and assembly line protective trims
Construction and architectural details
For architects and fabricators, tread strip provides an industrial aesthetic and practical protection:
- Wall corner guards and wainscot protection
- Elevator interiors, service doors, and utility panels
- Decorative trims, feature strips, and base protection
Consumer goods and OEM components
Thin tread strip integrates well into stamped or formed products:
- Appliance panels and trim
- Storage products, cabinets, and reinforcement skins
- Sport and leisure equipment housings
Fabrication Notes (Customer-Friendly)
| Process | Suitability | Tips for Best Results |
|---|---|---|
| Bending / press brake | Very good (alloy/temper dependent) | Choose O/H22/H24 for tighter bends; mind tread orientation |
| Stamping / punching | Excellent | Use sharp tooling; support thin gauges to reduce distortion |
| Roll forming | Excellent | Specify flatness and consistent pattern geometry |
| Joining | Riveting, bonding, welding (alloy dependent) | For welding, 5xxx is common; keep surface clean and oxide-free |
| Finishing | Anodizing, painting, coating | Confirm pattern + finish appearance requirements |
Quality and Supply Options
| Quality Aspect | Typical Customer Requirement |
|---|---|
| Consistent emboss depth | Stable traction and appearance in production batches |
| Surface scratch control | Film + interleave for visible parts |
| Traceability | Heat/coil identification for OEM control |
| Packaging | Export-worthy coils, edge protectors, moisture barrier if needed |
How to Specify for Quotation (Fast and Clear)
To receive a precise quote and lead time, provide:
| Needed Detail | Example |
|---|---|
| Alloy + temper | 3003 H24 |
| Thickness × width | 0.6 mm × 450 mm |
| Pattern type | Diamond / 5-bar |
| Finish | Mill finish + PE film |
| Coil ID / max OD | ID 300 mm; max OD 1400 mm |
| Quantity | 10 tons; split into 2-ton coils |
| End use | Roll forming panels (helps us recommend tolerances) |
Strips Aluminum Tread Plate Mold 0.018–1.0mm Thick delivers traction, stiffness, and corrosion resistance in a lightweight format optimized for modern fabrication. With flexible alloy options (1xxx/3003/5052), multiple tempers, and customizable tread patterns, it fits everything from vehicle interiors and industrial guarding to architectural protection and OEM components-all while keeping processing efficient and material usage economical.
https://www.alusheets.com/a/strips-aluminum-tread-plate-mold-0018-10mm-thick.html
